#!/bin/sh
#
# Bacula interface to mtx autoloader
#
#   Created  JAN/23/02 by Ludwig Jaffe
#
#  Works with the HP A4853 DLT Library
#         and the Storagetek Timberwolf 9730 DLT Library
#
#TAPEDRIVE0 holds the device/name of your 1st and only DLT drive (Bacula supports only 1 drive currently)
#
#Read TAPEDRIVE from command line parameters
if [ -z "$4" ] ; then
  TAPEDRIVE0=/dev/st0 
else
  TAPEDRIVE0=$4 
fi

#Delay in seconds the tape needs to load the tape. Needed to stop bacula from using the tape too early.
TAPEDELAY=65   #The StorageTek Timberwolf 9730 with DLT7000 needs approx. 50 seconds to load. 65 sec gives safety
MTXCHVERBOSE=1
if [ -z "$1" ] ; then
  echo ""
  echo "The mtx-changer script for bacula"
  echo "---------------------------------"
  echo ""
  echo "usage: mtx-changer <changer-device> <command> [slot] [devicename of tapedrive]"
  echo "       mtx-changer"
  echo ""
  echo "Valid commands:"
  echo ""
  echo "unload          Unloads a tape into the slot"
  echo "                from where it was loaded."
  echo "load <slot>     Loads a tape from the slot <slot>"
  echo "list            Lists full storage slots"
  echo "loaded          Gives slot from where the tape was loaded."
  echo "                0 means the tape drive is empty."
  echo "slots           Gives Number of aviable slots." 
  echo ""
  echo "Example:"
  echo "  mtx-changer /dev/changer load 1   loads a tape from slot1"
  echo ""
  exit
fi


case "$2" in 
   unload)
#     At first do mt -f /dev/st0 offline to unload the tape because HP A4853 aka Timberwolf9730
#     refuses to unload the tape from the drive if the DLT streamer did not unloaded it!!!
#
      #Check if you want to fool me
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Checking if drive is loaded before we unload. I Request loaded" ; fi
      mtx -f $1 status >/tmp/mtx.$$
      rm -f /tmp/mtxloaded
      cat /tmp/mtx.$$ | grep "^Data Transfer Element 0:Full" | awk "{print \$7}" > /tmp/mtxloaded
      rm -f /tmp/mtx.$$
      read LOADEDVOL </tmp/mtxloaded
      if [ -z "$LOADEDVOL" ] ; then
         LOADEDVOL=0
         echo "mtx-changer:  *** Don't fool me! *** The Drive $TAPEDRIVE0 is empty."
         echo ""
      else
        if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Doing mt -f $TAPEDRIVE0 offline to rewind and unload the tape!" ; fi
        mt -f $TAPEDRIVE0 offline
        if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Doing mtx -f $1 $2"  ; fi
        mtx -f $1 $2
      fi
      ;;

   load)
      #Let's check if drive is loaded before we load it
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Checking if drive is loaded before we load. I Request loaded" ; fi
      mtx -f $1 status >/tmp/mtx.$$
      rm -f /tmp/mtxloaded
      cat /tmp/mtx.$$ | grep "^Data Transfer Element 0:Full" | awk "{print \$7}" > /tmp/mtxloaded
      rm -f /tmp/mtx.$$
      read LOADEDVOL </tmp/mtxloaded 
      if [ -z "$LOADEDVOL" ] ; then 
         LOADEDVOL=0
         echo "mtx-changer: The Drive $TAPEDRIVE0 is empty." 
      else
         #Check if you want to fool me
         if [ $LOADEDVOL -eq $3 ] ; then 
           echo "mtx-changer: *** Don't fool me! *** Tape $LOADEDVOL is already in drive $TAPEDRIVE0!"
           echo "" 
           exit
         fi
         echo "mtx-changer: The Drive $TAPEDRIVE0 is loaded with the tape from slot $LOADEDVOL"
         echo "mtx-changer: Unloading..."
         if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Doing mt -f $TAPEDRIVE0 offline to rewind and unload the tape!" ; fi
         mt -f $TAPEDRIVE0 offline
         if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Doing mtx -f $1 unload"  ; fi
         mtx -f $1 unload
      fi
      #rm -f /tmp/mtxloaded
      #It is now insured that the drive is empty
      #
      #Now we can load the drive as desired 
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Doing mtx -f $1 $2 $3" ; fi
      mtx -f $1 $2 $3
      if [ $? -eq 0 ] ; then
        #Wait until the tape is fully loaded in the dlt drive. It takes about 50 seconds. For safety wait 65 seconds
        echo "Successfully loaded tape $3 into drive $TAPEDRIVE0."
        echo "Waiting $TAPEDELAY seconds for the drive to fully load the tape ..."
        sleep $TAPEDELAY
        echo "$TAPEDELAY seconds are gone. The tape should be fully loaded now."
        echo "Loading finished." ;
        exit 0
      else
        echo "ERROR loading tape $3 into drive $TAPEDRIVE0. Maybe, slot $3 is empty!"
        exit $?
      fi
      ;;

   list) 
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Requested list"; fi
#old      mtx -f $1 status | grep "^[     ]*Storage Element [0-9]*:.*Full" | awk "{print \$3}" | sed "s/:.*$/ /g" | tr -d "[\r\n]"
#from mtx bacula 1.29:
#     mtx -f $1 status | grep " *Storage Element [0-9]*:.*Full" | awk "{print \$3}" | sed "s/:.*$/ /g" | tr -d "[\r\n]"
      mtx -f $1 status | grep " *Storage Element [0-9]*:.*Full" | awk "{print \$3 \$4}" | sed "s/Full *\(:VolumeTag=\)*//"

      ;;

   loaded)
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Request loaded" ; fi
      mtx -f $1 status >/tmp/mtx.$$
      cat /tmp/mtx.$$ | grep "^Data Transfer Element 0:Full" | awk "{print \$7}" 
      cat /tmp/mtx.$$ | grep "^Data Transfer Element 0:Empty" | awk "{print 0}"  
      rm -f /tmp/mtx.$$
      ;;

   slots)
      if [ $MTXCHVERBOSE -eq 1 ] ; then echo "mtx-changer: Request slots" ; fi
      mtx -f $1 status | grep "[  ]Storage Changer" | awk "{print \$5}"
      ;;
esac