---------------------------------------------------------------------
GraphLCD driver library

The T6963C driver
---------------------------------------------------------------------

Description
-----------
The T6963C driver supports LC displays that use the Toshiba T6963C
controller, connected to the parallel port of your PC.


Wirings
-------
The T6963C driver supports the following connections on a parallel
port:
 - Standard (used by LCDproc)
 - Windows (used by many windows programs)

Standard wiring:

  printerport   LCD          other
  -----------   ----------   ----------
  GND    (18)   GND   (01)   GND          (Ground)
  nSTRB  (01)   WR    (06)                (Write)
  nAUTO  (14)   CE    (15)                (Chip Enable)
  INIT   (16)   C/D   (04)                (Command/Data)
  nSEL   (17)   RD    (05)                (Read)
  D0     (02)   D0    (07)                (Data Bit 0)
  D1     (03)   D1    (08)                (Data Bit 1)
  D2     (04)   D2    (09)                (Data Bit 2)
  D3     (05)   D3    (10)                (Data Bit 3)
  D4     (06)   D4    (11)                (Data Bit 4)
  D5     (07)   D5    (12)                (Data Bit 5)
  D6     (08)   D6    (13)                (Data Bit 6)
  D7     (09)   D7    (14)                (Data Bit 7)

Windows wiring:

  printerport   LCD          other
  -----------   ----------   ----------
  GND    (18)   GND   (01)   GND          (Ground)
  nSTRB  (01)   CE    (15)                (Chip Enable)
  nAUTO  (14)   RD    (05)                (Read)
  INIT   (16)   WR    (06)                (Write)
  nSEL   (17)   C/D   (04)                (Command/Data)
  D0     (02)   D0    (07)                (Data Bit 0)
  D1     (03)   D1    (08)                (Data Bit 1)
  D2     (04)   D2    (09)                (Data Bit 2)
  D3     (05)   D3    (10)                (Data Bit 3)
  D4     (06)   D4    (11)                (Data Bit 4)
  D5     (07)   D5    (12)                (Data Bit 5)
  D6     (08)   D6    (13)                (Data Bit 6)
  D7     (09)   D7    (14)                (Data Bit 7)

Note: The pin numbering may vary with other displays.

The LCD must operate in the 6x8 or 8x8 font mode. Usually, there is a
pin to choose 6x8 or 8x8 font mode.

There are Displays that have a pin to select the number of characters
per line. In that case, you have to select (width (in pixels) / 6) or
(width (in pixels) / 8) characters per line.

Attention: You have to tie these pins to +5V or GND. Don't leave them
open circuit or you will get unpredictable results.

Because the T6963 driver reads the status of the display, it might be
neccessary to enable the bidirectional mode in the BIOS and to enable
bidirectional mode in the Linux kernel:
 <*> Parallel port support
  <*>   PC-style hardware
  [*]   IEEE 1284 transfer modes


Configuration Parameters
------------------------
The T6963C driver supports the following parameters in config file:

Device
 Instead of using the direct output via port address (see Port), you
 can use the parport device (/dev/parportX). The advantage over the
 direct output via port address is that this works for non-root users
 also. But it's a little bit slower. The modules ppdev.o, parport.o
 and parport_pc.o must be loaded or compiled into the kernel.

Port
 Sets the port address of the parallel port. If this parameter is not
 given, 0x378 is used. To use this direct output, the program that
 uses the driver library has to be started with user 'root'.

Width
 Sets the horizontal size of the display. If this parameter is not
 given, a default value of 240 pixels is used.

Height
 Sets the vertical size of the display. If this parameter is not
 given, a default value of 128 pixels is used.

UpsideDown
 Rotates the display output by 180 degrees. This might be useful, if
 the LCD is mounted upside-down.
 Possible values: 'yes', 'no'
 Default value: 'no'

Invert
 Inverts the display.
 Possible values: 'yes', 'no'
 Default value: 'no'

RefreshDisplay
 Normally, most of the drivers do not update the whole display, but
 only the areas that have changed since last update. So it might be,
 that some faulty pixels would stay a longer time. To avoid this, the
 plugin makes a complete refresh from time to time. This parameter
 defines how often a complete refresh will be done.
 e.g.: A value of 5 means, that the plugin will make a complete
       refresh on every 5th update.
 A value of 0 completely disables complete refreshs. 
 Possible values: 0 <= x <= 50
 Default value: 5

Wiring
 Select the type of wiring your display is connected with.
 Possible values: 'Standard', 'Windows'
 Default value: 'Standard'

FontSelect
 Select the font width your display uses for text mode. In most cases
 this is selectable through one of the pins of your LCD board
 Possible values: '6', '8'
 Default value: '6'

AutoMode
 Enables or disables the usage of T6963C's auto mode which doubles
 writing speed when enabled.
 Possible values: 'yes', 'no'
 Default value: 'yes'

StatusCheck
 Enables or disables the usage of T6963C's status check. When using a
 shielded cable for connecting your display, the disabling may be
 possible. This results in doubling the speed of writing data to the
 LCD.
 Possible values: 'yes', 'no'
 Default value: 'yes'