Sophie: howto-html-ja-10.1-4mdv2008.1 noarch

howto-html-ja-10.1-4mdv2008.1.noarch.rpm

<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2 Final//EN">
<HTML>
<HEAD>
 <META NAME="GENERATOR" CONTENT="SGML-Tools 1.0.9">
 <TITLE>Linux Soundblaster 16 PnP Mini-Howto: isapnp.conf $B$NNc(B</TITLE>
 <LINK HREF="Soundblaster-16-3.html" REL=next>
 <LINK HREF="Soundblaster-16-1.html" REL=previous>
 <LINK HREF="Soundblaster-16.html#toc2" REL=contents>
</HEAD>
<BODY>
<A HREF="Soundblaster-16-3.html">$B<!$N%Z!<%8(B</A>
<A HREF="Soundblaster-16-1.html">$BA0$N%Z!<%8(B</A>
<A HREF="Soundblaster-16.html#toc2">$BL\<!$X(B</A>
<HR>
<H2><A NAME="s2">2. <CODE>isapnp.conf</CODE> $B$NNc(B</A></H2>

<P>$B0J2<$O!";d$N(B <CODE>isapnp.conf</CODE> $B%U%!%$%k$N%3%T!<$G$9!#%U%!%$%kFb$N(B
$B%3%a%s%H$NB?$/$O>JN,$7$F$$$^$9!#(B
<P>
<BLOCKQUOTE><CODE>
<PRE>
# Trying port address 0203
# Board 1 has serial identifier 67 00 00 40 17 2b 00 8c 0e

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier 67 00 00 40 17 2b 00 8c 0e)
# CTL002b Serial No 16407 [checksum 67]
# Version 1.0, Vendor version 2.0
# ANSI string -->Creative SB16 PnP&lt;--
#
# Logical device id CTL0031
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL002b/16407 (LD 0
#     ANSI string -->Audio&lt;--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
(DMA 0 (CHANNEL 1))
(DMA 1 (CHANNEL 5))
(IO 0 (BASE 0x0220))
(IO 1 (BASE 0x0330))
(IO 2 (BASE 0x0388))
(ACT Y)
))

(CONFIGURE CTL002b/16407 (LD 1
(INT 0 (IRQ 11 (MODE +E)))
(IO 0 (BASE 0x01e8))
(IO 1 (BASE 0x03ee))
 (ACT Y)
))


(CONFIGURE CTL002b/16407 (LD 2
#     ANSI string -->StereoEnhance&lt;--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0100
#         Maximum IO base address 0x0138
#         IO base alignment 8 bytes
#         Number of IO addresses required: 1
#(IO 0 (BASE 0x0100))
#(ACT Y)
))


(CONFIGURE CTL002b/16407 (LD 3
(IO 0 (BASE 0x0200))
(ACT Y)))
</PRE>
</CODE></BLOCKQUOTE>
<P>
<HR>
<A HREF="Soundblaster-16-3.html">$B<!$N%Z!<%8(B</A>
<A HREF="Soundblaster-16-1.html">$BA0$N%Z!<%8(B</A>
<A HREF="Soundblaster-16.html#toc2">$BL\<!$X(B</A>
</BODY>
</HTML>